...
2025-08-15 18:50
1690
...
2025-08-15 18:14
2198
...
2025-08-15 18:11
1483
...
2025-08-15 17:52
2128
...
2025-08-15 17:42
162
...
2025-08-15 17:42
2233
...
2025-08-15 17:34
790
...
2025-08-15 17:05
825
...
2025-08-15 16:46
1826
...
2025-08-15 16:40
1683
- - transport solids hydraulically
- method and level of design reach international advanced level. The company has the first-class pump performance
- The most important thing here is to determine the pump power required to deliver a specific fluid flow at the desired or required differential pressure. Consider the following.
- >Slurry Pump VS Mud Pump
- What we mean by slurry is basically a liquid containing solid particles. When you want to pump this slurry, there are different requirements than when pumping only dirty water. A waste water pump cannot handle the solid particles of a slurry. This is where slurry pumps come in handy. , Slurry pumps, are heavy duty and robust versions of centrifugal pumps, capable of handling tough and abrasive tasks.
- AIER will always strive to be your common sense slurry pump and parts supplier in a complex world!
- Find the best position that allows the pump to run as slowly as possible (to reduce wear) but fast enough to prevent solids from settling and clogging the piping.
- With the standard flush schedule, the flow is usually adjusted by compressing the packings until a few drops of water are observed leaking from the seals on the drive side. In a quench schedule the flow rate is set by adjusting the inlet valve, while a valve is used on the exhaust side to maintain the correct seal tank pressure. If the outlet water from the seal box is too hot, the flow rate is increased until the outlet water cools, while still maintaining the correct seal box pressure.
- Typical Applications of slurry pump
- The concentration of solids in the slurry - measured as a percentage of the total volume.
- Rubber lined pumps offer many advantages
- Typically, slurries are.
- Choosing The Right Slurry Pump For Your Application
- Larger impellers made of more material. This is to compensate for the wear and tear caused by abrasive slurries.
- Aier Machinery Hebei Co., Ltd. is a large-scale professional >slurry pumps manufacturer, gravel pumps, dredge pumps, sewage pumps and clean water pumps in China.
- Packing the box seal
- Pumps designed to pump slurries will be heavier than pumps designed for less viscous liquids because slurries are heavy and difficult to pump.
- Choosing Dry Slurry Pumps Versus Submersible Slurry Pumps
- Slurry Pump
- Slurry Pump Impeller Size
- Stainless Steel, Duplex Stainless Steel, Ductile Iron, Grey Iron, etc. We can also provide natural rubber, elastomer rubber parts and pumps.
- What is 'slurry'?
- There is a better way to pump sewage, overflows and other collected dirty water around the plant.
- A quench plan, as the name indicates, is designed to quench or cool the seal. It is normally used if short periods of dry running are expected. As illustrated bellow, the fluid is introduced into the area between the back of the seal faces and the close fit exit on the drive side of the pump.
- Settling slurries are formed by coarse particles, which tend to form unstable mixtures. Special attention should be paid to flow and power calculations when selecting a pump. Most slurry applications consist of coarse particles and therefore have a higher abrasion resistance.
- Follow proper piping principles to ensure consistent and uniform delivery of mud to the pump.
- >Dredge Pump
- Slurry pumps can also simply axially adjust the clearance between the impeller and the adjacent throat casing sealing surface. This helps to maintain pump performance when internal components begin to wear.
- Longer maintenance intervals
- With the development of the dredging market, the requirements for dredging equipment are getting higher and higher, and the suction resistance and vacuum of dredging pumps are getting higher and higher, which has a great impact on the efficiency of dredging pumps and the chance of cavitation is getting higher and higher. The number of , dredging pumps, is also increasing.
- If a centrifugal pump, is the design and material used to construct the impeller suitable for pumping slurries?
- Slurries are divided into two main categories: non-settling or settling. Non-settling slurries consist of very fine particles, giving the illusion of increased apparent viscosity. These slurries usually have low wear characteristics, but require very careful consideration when selecting the right pump, as they behave differently from ordinary liquids.
- 600WN to 1000WN dredge pumps are of double casings, single stage cantilevered centrifugal pumps. These pumps are equipped with frame and lubrication is force thin oil. The design of double casing the pump working till the volute liner almost worn down and guarantee no leakage when volute liner is worn down.
- Lifetime use
- 600WN to 1000WN dredge pumps are of double casings, single stage cantilevered centrifugal pumps. These pumps are equipped with frame and lubrication is force thin oil. The design of double casing the pump working till the volute liner almost worn down and guarantee no leakage when volute liner is worn down.
- Mixers can also help agitators when pumping very dense particles. In applications where the tank is small and/or where pumping is desired to lower the water level in the tank, a slurry pump with an internal cooling system should be considered to avoid overheating of the stator (when the water level gets low). When pumping sediment from a dam or lagoon, consider the use of a raft unit, which is a submersible device. Agitators are recommended, as well as one or more mixers that can be mounted on the raft or pump to resuspend particles for successful pumping of particles.
- Floor drainage
- Definition of dredge and slurry pumps
- testing station in the world, and its test capacity can reach 13000m³/h. Annual output of our products is 10000
- Dredge pumps are designed to transfer large quantities of fluids and solids.
- One problem with centrifugal pumps is that the velocity and shear forces within the pump may damage the slurry/solids. Typically, twin-screw pumps cause the least damage to solids in the slurry.
- What are the materials used to construct the pump?
- Chromium White Iron, Super High Chromium Hypereutectic White Iron, Low Carbon High Chromium Alloy, Carbon Steel,
- Slurry Pump
- sets or tons on high chrome alloy castings. Main products are Type WA, WG, WL, WN, WY, WZ, etc. Size: 25-1200mm,
- What is 'slurry'?
- What is a slurry?
- - Pumping media where abrasive particles are present
- Our firm has strong technical force and is specially engaged in the research of abrasion resistant materials of slurry pumps, sewage pumps and water pumps and the development of new products. The materials include high chrome white iron, duplex stainless steel, stainless steel, ductile iron, rubber, etc.
- - Keeping clean catch basins clean from solids