Not lower 5%

Other experts say there is simply no conclusive evidence at this point that titanium dioxide is damaging to humans after ingesting. Kaminski in particular said the research studies cite health hazards that were found by using high doses of the product, which you would not normally see in food.

Lithopone 30% has a lower coverage power than titanium dioxide. For this reason, Lithopone 30% can only partially substitute titanium dioxide, between 5 and 40%. 

In vitro, in the hemocytes of the marine mussel Mytilus hemocytes, suspension of TiO₂ NPs (Degussa P25, 10 μg/ml) stimulated immune and inflammatory responses, such as lysozyme release, oxidative burst and nitric oxide production. Vevers and Jha demonstrated the intrinsic genotoxic and cytotoxic potential of TiO₂ NPs on a fish-cell line derived from rainbow-trout gonadal tissue (RTG-2 cells) after 24 h of exposure to 50 μg/ml. Reeves et al. demonstrated a significant increase in the level of oxidative DNA damage in goldfish cells, and suggested that damage could not repaired by DNA repair mechanisms. Another suggestion from the mentioned study was that hydroxyl radicals are generated also in the absence of UV light. It has been shown that fish cells are generally more susceptible to toxic/oxidative injury than mammalian cells.

The calcined product obtained by the ordinary zinc-barium white preparation method is beaten into a slurry, which is then surface-treated with sodium silicate, aluminum sulfate or sodium aluminate and surfactant, and then filtered, washed, dried and pulverized. Can.

Because of its unique pigment and fine-milled texture, titanium dioxide has become popular over the past century in a wide variety of different products. These include adhesives, paints, plastics, rubbers, textiles, inks, ceramics, and even some pharmaceuticals, foods, and hygiene products.

2: Clarification mechanism of coagulant

Chemical coagulation is a process in which chemical agents (coagulants) are added to water treatment to make colloidal dispersion system destabilize and agglomerate. In the coagulation process, small suspended particles and colloidal impurities are aggregated into larger solid particles to separate particulate impurities from water, which is called coagulation clarification.

After adding coagulant into water, colloidal particles and other small particles can be polymerized into larger flocs through the comprehensive action of mixing, coagulation and flocculation. The whole process of coagulation and flocculation is called coagulation.

(1) Destabilization and condensation of colloids

Adding electrolyte to water can compress the electric double layer and destabilize the colloid. The main mechanism is that the electric double layer of colloidal particles in water is compressed or neutralized by adding aluminum salt or iron salt coagulant. The coagulant and raw water are mixed rapidly and evenly, and a series of chemical reactions are produced to destabilize. This process takes a short time, generally about 1 min. Some cationic polymers can also play a role in the destabilization and condensation of colloids in water. These polymers have a long chain structure and positive charge in water. Their destabilization and condensation of colloids in water is due to the interaction of van der Waals force adsorption and electrostatic attraction.

(2) Flocculation and formation of floc (alum)

The particle size of the initial flocculate formed by colloid destabilization and coagulation in water is generally more than 1 m. at this time, Brownian motion can no longer push them to collide and form larger particles. In order to make the initial flocs collide with each other to form large flocs, it is necessary to input additional energy into the water to produce a velocity gradient. Sometimes it is necessary to add organic polymer flocculant into water, and the adsorption bridging effect of long chain molecules of flocculant is used to improve the probability of collision and adhesion. Flocculation efficiency usually increases with the increase of flocculate concentration and flocculation time.

Compared with polyaluminum chloride, polyaluminum chloride has the advantages of high density, fast settling speed and wide pH adaptability; the coagulation effect is less affected by temperature than that of polyaluminum sulfate; however, when adding ferric salt, it should be noted that when the equipment is not in normal operation, the iron ions will make the effluent color, and may pollute the subsequent desalination equipment.