Apart from proximately neuromorphic technologies, TiO2-based memristors have also found application in various sensors. The principle of memristive sensorics is based on the dependency of the resistive switching on various external stimuli. This includes recording of mechanical energy (Vilmi et al., 2016), hydrogen detection (Hossein-Babaei and Rahbarpour, 2011; Strungaru et al., 2015; Haidry et al., 2017; Vidiš et al., 2019), γ-ray sensing (Abunahla et al., 2016), and various fluidic-based sensors, such as sensors for pH (Hadis et al., 2015a) and glucose concentration (Hadis et al., 2015b). In addition, TiO2 thin films may generate photoinduced electron–hole pairs, which give rise to UV radiation sensors (Hossein-Babaei et al., 2012). Recently, the biosensing properties of TiO2-based memristors have been demonstrated in the detection of the bovine serum albumin protein molecule (Sahu and Jammalamadaka, 2019). Furthermore, this work has also demonstrated that the introduction of an additional graphene oxide layer may effectively prevent the growth of multidimensional and random conductive paths, resulting in a lower switching voltage, better endurance, and a higher resistance switching ratio. This opens up a new horizon for further functional convergence of metal oxides and two-dimensional memristive materials and interfaces (Zhang et al., 2019a).
Particle size: optimum particle size to produce maximum opacity is 200–300 nm.
Different from common zinc barbed rope, high zinc barbed rope surface zinc content is very high can reach 6-8 times of the former, so there is a great advantage in the service life, ordinary products begin to corrosion three to five years while the latter will take longer to change. Stainless steel barbed rope is in material protection so durability is also better, these two products are long service life, but in terms of high price.
In the process of production, the acid activation solution can remove the corrosion products and oxide film on the surface of low carbon steel wire without excessive corrosion on the matrix. Galvanized wire can be used zincate galvanized or chloride galvanized process, appropriate additives should be used to obtain the coating required by the standards of low carbon steel wire. When galvanized wire out of the light plating should be carried out light treatment. The bath temperature of galvanized wire should be controlled well.
Cyanogen bath has alkaline zincate bath, ammonium bath, sulfate bath and ammonia chloride bath. Cyanide galvanized solution plating ability is good, the coating lubrication, in production has been selected for a long time, steel mesh chromium plating: chromium plating layer has a high hardness, according to the bath composition and process conditions are different, the hardness can be changed in a large scale 400~1200HV.
Removal of surface-active substances by activated carbon matting. Or make the bubble unstable according to overworry, these are all reasonable countermeasures; Other strategies should also be used to minimize the amount of surfactant taken in. The introduction of organic matter can make the electroplating process speed drop sharply. Galvanized iron wire blackening can be effectively prevented, such as: the work site to keep dry, reduce and do not use chemicals, operators with clean gloves and so on. In addition, hot dipping zinc factory can be required, after dipping zinc must be passivation treatment, passivation treatment of zinc has a better anti-discoloration effect, can effectively prolong the discoloration time, the combination of the two, discoloration should be able to solve.
In order to pack and bundle galvanized wire on the surface of the deposit layer to remove the surface film, surface inclusion and other defects can be found and treated by conventional technology; Excess foam is caused by soaps and saponable fatty surfactants being brought into the tank. Moderate foam formation rates may be harmless. Small homogeneous particles of large denier present in the tank can stabilize the foam layer. To remove surface active substances by matting with activated carbon. Or filtration to make the foam less stable, which are effective measures; Other measures should also be taken to reduce the intake of surfactant. The electroplating speed can be significantly reduced by the introduction of organic matter. Although the chemical formula is conducive to a high deposition rate, the coating thickness cannot meet the requirements after the organic matter is loaded, so activated carbon can be used to treat the tank.
The corrosion or discoloration of galvanized iron wire in the atmosphere caused by oxygen, moisture and other pollution impurities is called rust or rust. After galvanized iron wire rusting, it will affect the appearance quality, seriously affect the use, and even cause scrap, so galvanized iron wire must be properly kept and pay attention to rust prevention.