products with titanium dioxide



Pure PVB is non-toxic and harmless to human body. In addition, ethyl acetate or alcohol can be used as solvent, so PVB is widely used in printing ink of food containers and plastic packaging in European and American countries.

Storage safety properties

PVB can be stored for two years without affecting its quality as long as it is not in direct contact with water; PVB shall be stored in a dry and cool place and avoid direct sunlight. Heavy pressure shall be avoided during PVB storage.

Solubility

PVB is soluble in alcohol, ketone, ester and other solvents. The solubility of various solvents changes according to the functional group composition of PVB itself. Generally speaking, alcohol solvents are soluble, but methanol is more insoluble for those with high acetal groups; The higher the acetal group, the easier it is to dissolve in ketone solvents and ester solvents;

PVB is easily soluble in cellosolve solvents; PVB is only partially dissolved in aromatic solvents such as xylene and toluene; PVB is insoluble in hydrocarbon solvents.

Viscosity characteristics of PVB solution

The viscosity of PVB solution is greatly affected by the formula of solvent and the type of solvent; Generally speaking, if alcohol is used as solvent, the higher the molecular weight of alcohol, the higher the viscosity of PVB solution;

Aromatic solvents such as xylene and toluene and hydrocarbon solvents can be used as diluents to reduce the viscosity of PVB solution; The effect of PVB chemical composition on viscosity is summarized as follows: under the same solvent and the same content of each base, the higher the degree of polymerization, the higher the solution viscosity; Under the same solvent and the same degree of polymerization, the higher the acetal group or acetate group, the lower the solution viscosity.

Dissolution method of PVB

Where mixed solvents are used, the dissolution step is to first put aromatic solvents (such as xylene, toluene, etc.) or ester solvents (such as n-butyl acetate, ethyl acetate, etc.) into the mixing, slowly put PVB into the mixing, and then add alcohol solvents (such as n-butanol, ethanol, etc.) after PVB is dispersed and expanded,

At this time, the dissolution time can be shortened by heating; Using this dissolution method, the formation of lumpy PVB can be avoided (because the dissolution time will be several times after the formation of lumpy PVB), so the dissolution speed can be accelerated. Generally, the ratio of aromatic and alcohol solvents is 60 / 40 ~ 40 / 60 (weight ratio), and PVB solution with low viscosity can be prepared.

The solvent composition contains 2 ~ 3wt% water, which can improve the hydrogen bonding strength of alcohol solvents and help the solubility of PVB.

Processing properties

Although PVB resin is a thermoplastic, it has little processability before plasticizer is added. Once plasticizer is added, its processability is very easy.

The purpose of general coatings and adhesives is to change the resin characteristics by adding plasticizers to meet the application requirements, such as film softness, reducing the TG point of the resin, reducing the heat sealing temperature, maintaining low-temperature softness, etc.

Compatibility

PVB can be compatible with a variety of resins, such as phenolic resin, epoxy resin, alkyd resin and MELAMINE resin.

B-08sy, b-06sy and b-05sy with high acetal degree can be mixed with nitrocellulose in any proportion. PVB and alkyd resin are partially compatible. General PVB is compatible with low molecular weight epoxy resin, while high molecular weight epoxy resin needs PVB with high acetal degree to be compatible with each other.

...
products with titanium dioxide2025-08-15 02:08
502
{随机栏目} 2025-08-15 01:54 2417

    • Latest articles

  • When choosing your control components, remember that the best control boxes use the simplest control component appropriate for the application, so start simple and work your way up. You don’t need to use a PLC where a simpler (and less expensive) component will do the job.

  • You should use a minimum of two half-lapped layers of vinyl tape to insulate and jacket low-voltage components. A half-lap (see Figure above) consists of overlaying each turn by one-half the width of the tape. The general rule of thumb calls for a tape thickness of 1.5 times the thickness of existing wire or cable insulation. In every case, tension on the tape should be sufficient to conform the tape evenly to the surface. A slight reduction in tension is encouraged for the final wrap. Trim the tape end and allow it to return to shape before pressing down with the thumb to avoid lifting or flagging.

  • Car loom tape is designed with specific properties to withstand the harsh conditions within a vehicle. It is heat-resistant to endure the high temperatures produced by engines, and its insulating properties protect against electrical shorts. Moreover, its adhesive strength ensures it stays in place despite the constant movement and of the car.
  • Yellow
  • One of the most notable features of this tape is its waterproof capabilities. Whether it's used to seal electrical connections, repair water pipes, or protect outdoor equipment from moisture, it consistently delivers a robust and reliable barrier against water ingress. Its waterproofing prowess is particularly valuable in harsh environments, where exposure to rain, humidity, or even submersion can pose significant challenges.

  • The Versatility and Benefits of Silicone Insulation Tape


  • The Significance of Automotive Wire Harness Wrapping Tape in Modern Vehicles

  • In addition to its electrical uses, this tape proves invaluable for plumbing and HVAC applications, where it can seal leaks and provide thermal insulation. DIY enthusiasts also appreciate its versatility for home repairs, crafts, and even outdoor projects.


  • Rubber Adhesives

  • What is silicone tape used for?

  • In addition to its practical applications, EPR self-amalgamating tape is also known for its durability. Once applied, the tape forms a strong and flexible bond that can withstand even the harshest conditions. This makes it a cost-effective solution for long-term repairs and maintenance projects.

  • Electrical tapes are versatile, suited to a multitude of tasks, and when installed properly provide a long-term, effective insulation. According to Anderson, both the NJATC headquarters and local training efforts are strongly supported by industry suppliers, which provide sample products and assist with course development and hands-on instruction. In addition, manufacturers of electrical-grade tapes are generally willing to provide technical support and instruction on proper taping techniques.

  • Choosing the correct control box is a crucial decision that impacts your electrical systems’ efficiency and safety. Here’s a guide to navigating this selection process:

  • The installation process of butyl rubber weather stripping is relatively straightforward and can be completed by following simple instructions. It typically involves measuring the area needing protection, cutting the strip to size, and applying it to the desired location using appropriate adhesives or mechanical fasteners. For DIY enthusiasts, this presents an opportunity to improve their home's energy efficiency and comfort level without requiring professional assistance.
  • Secondly, PVC is known for its robustness and resilience. It can withstand a wide range of temperatures, making it suitable for both indoor and outdoor applications. It is resistant to moisture, chemicals, and UV radiation, thereby protecting the wire core from corrosion and degradation over time. This ensures the longevity of electrical installations and reduces maintenance costs.