2: Clarification mechanism of coagulant

Chemical coagulation is a process in which chemical agents (coagulants) are added to water treatment to make colloidal dispersion system destabilize and agglomerate. In the coagulation process, small suspended particles and colloidal impurities are aggregated into larger solid particles to separate particulate impurities from water, which is called coagulation clarification.

After adding coagulant into water, colloidal particles and other small particles can be polymerized into larger flocs through the comprehensive action of mixing, coagulation and flocculation. The whole process of coagulation and flocculation is called coagulation.

(1) Destabilization and condensation of colloids

Adding electrolyte to water can compress the electric double layer and destabilize the colloid. The main mechanism is that the electric double layer of colloidal particles in water is compressed or neutralized by adding aluminum salt or iron salt coagulant. The coagulant and raw water are mixed rapidly and evenly, and a series of chemical reactions are produced to destabilize. This process takes a short time, generally about 1 min. Some cationic polymers can also play a role in the destabilization and condensation of colloids in water. These polymers have a long chain structure and positive charge in water. Their destabilization and condensation of colloids in water is due to the interaction of van der Waals force adsorption and electrostatic attraction.

(2) Flocculation and formation of floc (alum)

The particle size of the initial flocculate formed by colloid destabilization and coagulation in water is generally more than 1 m. at this time, Brownian motion can no longer push them to collide and form larger particles. In order to make the initial flocs collide with each other to form large flocs, it is necessary to input additional energy into the water to produce a velocity gradient. Sometimes it is necessary to add organic polymer flocculant into water, and the adsorption bridging effect of long chain molecules of flocculant is used to improve the probability of collision and adhesion. Flocculation efficiency usually increases with the increase of flocculate concentration and flocculation time.

Compared with polyaluminum chloride, polyaluminum chloride has the advantages of high density, fast settling speed and wide pH adaptability; the coagulation effect is less affected by temperature than that of polyaluminum sulfate; however, when adding ferric salt, it should be noted that when the equipment is not in normal operation, the iron ions will make the effluent color, and may pollute the subsequent desalination equipment.

Moreover, sustainability is becoming increasingly important in manufacturing practices. Companies that prioritize environmentally-friendly processes and ethically sourced materials can enhance their brand image and meet the rising consumer demand for sustainable products. While cheap titanium dioxide manufacturers may offer lower prices, businesses should also evaluate their commitment to sustainable practices and social responsibility.

Hemolysis was studied on suspensions of P25TiO₂NPs (0.2 mg/mL and 0.02 mg/mL), vitaminB2@P25TiO₂NPs (0.2 mg/mL and 0.02 mg/mL) and vitamin B2 (0.2 mg/mL and 0.02 mg/mL) were prepared and mixed with 500 μL of anticoagulated blood (donated by Laboratorio de Hemoderivados, UNC) in a rate of 1/10. A solution of NaCl 10% was used as the positive control and PBS as the negative control. Then, the samples were irradiated using the LED described above for 3 and 6 h to simulate the light penetration into the skin. Also, a set of samples was kept in the dark as control. Finally, the samples were centrifuged and the absorbance at 540 nm was measured in the supernatants. The experiment was reproduced twice; the standard deviation was calculated and p-value < 0.05 were considered significant.

Résumé–Cet article traite de la découverte de lithopone phosphorescent sur des dessins à l'aquarelle, datés entre 1890 et 1905, de l'artiste Américain John La Farge et de l'histoire du lithopone dans l'industrie des pigments à la fin du 19e et au début du 20e siècle. Malgré de nombreuses qualités souhaitables pour une utilisation en tant que blanc dans les aquarelles et les peintures à l'huile, le développement du lithopone comme pigment pour artistes a été compliqué de par sa tendance à noircir lorsqu'il est exposé au soleil. Sa disponibilité et son usage par les artistes demeurent incertains parce que les catalogues des marchands de couleurs n'étaient généralement pas explicites à indiquer si les pigments blancs contenaient du lithopone. De plus, lors d'un examen visuel, le lithopone peut être confondu avec le blanc de plomb et sa phosphorescence de courte durée peut facilement être ignorée par l'observateur non averti. À ce jour, le lithopone phosphorescent a seulement été documenté sur une autre œuvre: une aquarelle de Van Gogh. En plus de l'histoire de la fabrication du lithopone, cet article décrit le mécanisme de sa phosphorescence et son identification à l'aide de la spectroscopie Raman et de la spectrofluorimétrie.

From a stability standpoint, lithopone, a fusion of zinc sulfide and artificially precipitated barite, is non-toxic and exhibits resilience to mild lyes and acids. However, it is incompatible with colors containing copper. Despite its strong covering power in oil, lithopone’s drying capabilities are notably limited, posing potential issues for artists. Notably, early experimentation with lithopone-based grounds instead of zinc white resulted in undesirable darkening, although this blackness receded upon drying. This unpredictable behavior has sparked debate among scientific communities, emphasizing the need for further exploration and understanding of this pigment.

1. Introduction