1317-80-2 factory

Prof. Maged Younes, Chair of EFSA’s expert Panel on Food Additives and Flavourings (FAF), wrote of the decision: “Taking into account all available scientific studies and data, the Panel concluded that titanium dioxide can no longer be considered safe as a food additive. A critical element in reaching this conclusion is that we could not exclude genotoxicity concerns after consumption of titanium dioxide particles. After oral ingestion, the absorption of titanium dioxide particles is low, however they can accumulate in the body.”

...

The toxicity of P25TiO2NPs was evaluated in both prokaryotic (Fig. 3) and eukaryotic cells (Fig. 4). The XTT assay was chosen to measure the cell viability in bacterial cultures of MSSA, a normal skin microbiota microorganism. The reduction in the viability of samples with bare NPs is notorious, possibly due to the described ROS production from the interaction of P25TiO2NPs with light [37]. This effect seems to be avoided when they are functionalized with vitamin B2. Also, the most concentrated vitaminB2@P25TiO2NPs sample (0.2 mg/mL) shows up to 60% more absorbance after 6 h compared to the bare NPs (due to normal cell replication). This may indicate that the antioxidant effect of the vitamin B2 coating is greater than the oxidation damage produced by the NPs. This protective capacity could be attributed to the glutathione redox cycle and the conversion of reduced riboflavin to its oxidized form [38]. Values of cell viability greater than 100% are not rare and could be understood because the XTT assay actually measure metabolic activity when reducing the tetrazole to formazan. It is usually assumed that conversion is dependent on the number of viable cells, but it could also be related to an expected increased enzymatic activity when cells are exposed to small doses of some new substance. Further analysis showed that this effect was not the only one responsible for better cell viability of vitaminB@P25TiO2NPs treated samples.

...

A great number of other brands with fancy names have gone out of the German market, because of some defects in the processes of manufacture. The English exporters, as a rule, offer three or four grades of lithopone, the lowest priced consisting of about 12 per cent zinc sulphide, the best varying between 30 and 32 per cent zinc sulphide. A white pigment of this composition containing more than 32 per cent zinc sulphide does not work well in oil as a paint, although in the oilcloth and shade cloth industries an article containing as high as 45 per cent zinc sulphide has been used apparently with success. Carefully prepared lithopone, containing 30 to 32 per cent sulphide of zinc with not over 1.5 per cent zinc oxide, the balance being barium sulphate, is a white powder almost equal to the best grades of French process zinc oxide in whiteness and holds a medium position in specific gravity between white lead and zinc oxide. Its oil absorption is also fairly well in the middle between the two white pigments mentioned, lead carbonate requiring 9 per cent of oil, zinc oxide on an average 17 per cent and lithopone 13 per cent to form a stiff paste. There is one advantage in the manipulation of lithopone in oil over both white lead and zinc oxide, it is more readily mis-cible than either of these, for some purposes requiring no mill grinding at all, simply thorough mixing with the oil. However, when lithopone has not been furnaced up to the required time, it will require a much greater percentage of oil for grinding and more thinners for spreading than the normal pigment. Pigment of that character is not well adapted for use in the manufacture of paints, as it lacks in body and color resisting properties and does not work well under the brush. In those industries, where the paint can be applied with machinery, as in shade cloth making, etc., it appears to be preferred, because of these very defects. As this sort of lithopone, ground in linseed oil in paste form, is thinned for application to the cloth with benzine only, and on account of its greater tendency to thicken, requires more of this comparatively cheap thinning medium, it is preferred by most of the manufacturers of machine painted shade cloth. Another point considered by them is that it does not require as much coloring matter to tint the white paste to the required standard depth as would be the case if the lithopone were of the standard required for the making of paint or enamels. On the other hand, the lithopone preferred by the shade cloth trade would prove a failure in the manufacture of oil paints and much more so, when used as a pigment in the so-called enamel or varnish paints. Every paint manufacturer knows, or should know, that a pigment containing hygroscopic moisture does not work well with oil and driers in a paint and that with varnish especially it is very susceptible to livering on standing and to becoming puffed to such an extent as to make it unworkable under the brush. While the process of making lithopone is not very difficult or complicated, the success of obtaining a first class product depends to a great extent on the purity of the material used. Foreign substances in these are readily eliminated by careful manipulation, which, however, requires thorough knowledge and great care, as otherwise the result will be a failure, rendering a product of bad color and lack of covering power.

...