This constant high rate of ROS production leads rapidly to extreme macromolecular oxidation, here it is observed in the AOPP and MDA detected after 3 h in samples treated with bare P25TiO₂NPs (Fig. 6, Fig. 7). Macromolecular oxidation includes, among others, both protein and lipid oxidation. The ROS causes protein oxidation by direct reaction or indirect reactions with secondary by-products of oxidative stress. Protein fragmentation or cross-linkages could be produced after the oxidation of amino acid side chains and protein backbones. These and later dityrosine-containing protein products formed during excessive production of oxidants are known as advanced oxidation protein products (AOPP). They absorb at 340 nm and are used to estimate the damage to structural cell amino acids. Lipid oxidation is detected by the conjugation of oxidized polyunsaturated lipids with thiobarbituric acid, forming a molecule that absorbs light at 532 nm. Polyunsaturated lipids are oxidized as a result of a free-radical-mediated chain of reactions. The most exposed targets are usually membrane lipids. The macromolecular damage could represent a deadly danger if it is too extensive, and this might be the case. Moreover, it could be observed that cellular damage continues further and becomes irrevocable after 6 h and MDA could not be detected. This may be due to the fact that the lipids were completely degraded and cells were no longer viable. Lipids from the cell membrane are the most prone to oxidation. In fact, lipid peroxidation biomarkers are used to screen the oxidative body balance [51]. At the same time, AOPP values are up to 30 times higher for bare nanoparticles in comparison to the functionalized ones.

A great number of other brands with fancy names have gone out of the German market, because of some defects in the processes of manufacture. The English exporters, as a rule, offer three or four grades of lithopone, the lowest priced consisting of about 12 per cent zinc sulphide, the best varying between 30 and 32 per cent zinc sulphide. A white pigment of this composition containing more than 32 per cent zinc sulphide does not work well in oil as a paint, although in the oilcloth and shade cloth industries an article containing as high as 45 per cent zinc sulphide has been used apparently with success. Carefully prepared lithopone, containing 30 to 32 per cent sulphide of zinc with not over 1.5 per cent zinc oxide, the balance being barium sulphate, is a white powder almost equal to the best grades of French process zinc oxide in whiteness and holds a medium position in specific gravity between white lead and zinc oxide. Its oil absorption is also fairly well in the middle between the two white pigments mentioned, lead carbonate requiring 9 per cent of oil, zinc oxide on an average 17 per cent and lithopone 13 per cent to form a stiff paste. There is one advantage in the manipulation of lithopone in oil over both white lead and zinc oxide, it is more readily mis-cible than either of these, for some purposes requiring no mill grinding at all, simply thorough mixing with the oil. However, when lithopone has not been furnaced up to the required time, it will require a much greater percentage of oil for grinding and more thinners for spreading than the normal pigment. Pigment of that character is not well adapted for use in the manufacture of paints, as it lacks in body and color resisting properties and does not work well under the brush. In those industries, where the paint can be applied with machinery, as in shade cloth making, etc., it appears to be preferred, because of these very defects. As this sort of lithopone, ground in linseed oil in paste form, is thinned for application to the cloth with benzine only, and on account of its greater tendency to thicken, requires more of this comparatively cheap thinning medium, it is preferred by most of the manufacturers of machine painted shade cloth. Another point considered by them is that it does not require as much coloring matter to tint the white paste to the required standard depth as would be the case if the lithopone were of the standard required for the making of paint or enamels. On the other hand, the lithopone preferred by the shade cloth trade would prove a failure in the manufacture of oil paints and much more so, when used as a pigment in the so-called enamel or varnish paints. Every paint manufacturer knows, or should know, that a pigment containing hygroscopic moisture does not work well with oil and driers in a paint and that with varnish especially it is very susceptible to livering on standing and to becoming puffed to such an extent as to make it unworkable under the brush. While the process of making lithopone is not very difficult or complicated, the success of obtaining a first class product depends to a great extent on the purity of the material used. Foreign substances in these are readily eliminated by careful manipulation, which, however, requires thorough knowledge and great care, as otherwise the result will be a failure, rendering a product of bad color and lack of covering power.

Overall, the precipitation of titanium dioxide is a complex process that requires careful control of various factors to achieve the desired product properties. By optimizing the precipitation percentage and carefully monitoring the precipitation process, manufacturers can produce high-quality titanium dioxide that meets the stringent requirements of their customers in the paints, coatings, plastics, and cosmetics industries.

FAQ
Q1. Can I have a sample order for Titanum Dioxide?
A: Yes, We can express you 500 grams of samples, free of charge. And the quality is subject to the sample.

Q2. What about the lead time?
A: Within 15days after receiving the payment

Q3. Do you have any MOQ limit for Titanium Dioxidde?
A: 5MT

Q4. Is it OK to print my logo on the Titanium Dioxide Packing bag?
A: Yes. Please inform us formally before our production and confirm the design LOGO firstly.

Q5: What's the payment term?
A: T/T or L/C at sight